NCY CVT KIT (Metro, Ruckus GET)
Description: NCY CVT Kit GET aka Super CVT transmission kit for Metropolitan 2012 & older and all U.S. Honda Ruckus GET 50cc engines is one of the best dollar-for-dollar bolt-ons to improve your GET scooter transmission performance! Quicker acceleration, reach faster top speeds, and makes your GET CVT the smoothest running transmission in town! From rapid downshifting to slow cruising, this thing is smooth. Ultralight balanced components, oversized wear pads, and state of the art polytetrafluoroethylene (PTFE) coatings ensure superior performance and long service life.
NOTE: Does not fit Fuel Injected models. Recommend using a new belt with this kit. Belt and the belt drive facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. Must re-use stock variator ramp top, variator boss, washers, and nuts. Most parts also will fit Honda DIO's CVT.
Installation: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctite, torque nut to 30-35ft lbs. For reassurance please consult your manufacturer variator torque specs.
100% NCY Products - NO SUBSTITUTE
Includes the following Drive face, Roller weights, Variator, Secondary sliding sheave assembly, Springs, Clutch, and Clutch bell.1. Includes NCY Drive Face, Drive Face CNC-Machined
• 1x Aluminum CNC Machined Anodized Drive Face ID: 13.5mm (Splines 26) / OD: 95mm / H: 20.19mm
2. Includes NCY Variator 95mm, Roller weights, Variator housing, and Variator slides.
• 1x Alumin-Alloy Housing ID: 20mm / OD: 95mm / H: 31mm
• 6x Roller Weights (red): 16x13mm 7gm
• 3x Plastic Slides (red)
3. Includes NCY Secondary Sliding Sheave Assembly, slider (torque driver), O-rings, and clutch nut.
• 1x Rear Pulley Shaft ID: 17.43<21mm / OD: 34<45.1mm / H: 68.73mm
• 1x Rear Pulley Plate OD: 118.5mm
• 3x Secondary Slider Guides
• 3x Secondary Slider Pins
• 1x Secondary Slider Funnel ID: 33.5mm / OD: 43mm / H: 32.70mm
• 1x Secondary Slider Plate OD: 118.5mm
• 1x Secondary Spring Seat/Funnel ID: 43.3mm / OD: 45mm / H: 22.90mm
• 1x Stainless Steel Clutch Nut: 39mm
4. Includes NCY Compression Spring 1000 RPM, Compression spring.
• 1x Spring Comp (black): 1,000 RPM / L: 106mm
• Spring ID: 49.6mm / OD: 57.8mm
• Wire Gauge: 4mm
5. Includes NCY Clutch Performance, Clutch housing, Clutch springs, and Clutch weights.
• 1x Clutch ID: 24<28mm / OD: 105mm / H: 29.55mm
• 3x Clutch Spring (red): 2000 RPM
• 3x Clutch Weights (gray)
• 1x Clutch Nut: 39mm
6. Includes NCY Clutch Bell, Clutch bell.
• 1x Iron Clutch Bell Vented ID: 107mm / OD: 114.85mm / H: 34.54mm
• Splines: 22 / ID: 11<12mm / OD: 16.95mm / H: 17.75mm
• Made in Taiwan
• Fit Belt Size: 660-18-28 (Fit Metro ONLY)
• Fit Belt Size: 785-18-30 (Fit Ruckus ONLY)
• Fit Dowel Pin Set (8x14mm)
• Fit GET 49/50cc
Supported Models: Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, and virtually any scooter engine with these measurements.
Item Weight & Package Dimensions:
• 4.719 pounds | 17.5” (L) x 6.4” (W) x 5” (H)