Main Menu
Your Cart

NCY Secondary Bearing Spring Seat (DIO, GET, QMB)

NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)

Description: NCY Compression Spring Seat for 139QMB 49cc-50cc 4-stroke GY6 50 engine-based scooters, ATVs, and off-road karts. Also, fit Honda Dio/Elite and Honda GET only with conversion secondary pulley assembly.

NCY Compression Spring Seat aka NCY Secondary Spring Seat will allow for smoother torque spring action through the use of ball bearings. This allows the spring to pivot and turns freely rather than bind up.

Compatible with sport clutches on the market works on Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, and virtually any scooter engine with these measurements.

NOTE: This NCY Bearing Spring Seat measures 43mm I.D. Please verify before ordering. This NCY Bearing Spring Seat is for the Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke engines. Will work on Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model ONLY if you use WITH upgrade NCY Pulley Shaft, will NOT work with OEM pulley shaft. Before use, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.

Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.

Features:

•    Designed for Scooters Original State up to High-End Racing Conversion
•    Increased 15% Harder Spring by of the Spring Preload Twist Control 
•    Racing Twist Control for scooters and quads with engines from 139QMB, Kymco, Peugeot, Piaggio

Specifications:

Includes the following Bearings, and Bearing seat.

•    1x Bearing Seat ID: 47.4mm / OD: 57.6mm / H: 1.33mm
•    1x Bearings OD: 4mm
•    Made in Taiwan
•    Fit Clutch Nut: M28 / Socket: 39mm
    Fit Clutch: 105mm / Shaft: 155mm / Slider: 33.5mm / Pins: 6mm / Nut: M10 / Washer: M10 Bearing Funnel43mm / Bell Spline: 22 Socket: 14mm
•    Fit Belt Size: 
660-18-28785-18-30 (Fit GET ONLY)
•    Fit Belt Size: 669729, 788-18-30 (Fit QMB ONLY)
•    Fit Belt Size: 654669-18-30 (Fit DIO ONLY)
•    Fit Compression Spring: 1k1.5k2k rpm
•    Fit Clutch Springs: 1k1.5k2k rpm
•    Fit Dowel Pin Set (8x10mm)
•    Fit DIO 49/90cc+
•    Fit GET 49/50cc
•    Fit QMB 49/50cc+

Supported Models: NCY CVT Kit (Part# 1200-1171); Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, and virtually any scooter engine with these measurements.

-----
Item Weight & Product Dimensions:
•    0.043 Pounds | 2.267" (OD) x 1.866" (ID) x 0.157" (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
NCY Secondary Bearing Spring Seat (DIO, GET, QMB)
  • Stock: 28
  • Part #: 1200-1253
Sold: 13
Views: 4019
$19.95
Ex Tax: $19.95
Price in reward points: 20

Included