Main Menu
Your Cart

NCY Secondary Sliding Sheave Assembly (Honda Dio)

NCY Secondary Sliding Sheave Assembly (Honda Dio)
NCY Secondary Sliding Sheave Assembly (Honda Dio)
NCY Secondary Sliding Sheave Assembly (Honda Dio)
NCY Secondary Sliding Sheave Assembly (Honda Dio)
NCY Secondary Sliding Sheave Assembly (Honda Dio)
NCY Secondary Sliding Sheave Assembly (Honda Dio)

Description: NCY Secondary Sliding Sheave Assembly for Honda DIO 50cc-90cc scooter engines. This NCY adjustable secondary sliding sheave has two sets of ramp angles, one steeper than the other. These allow you to adjust how quickly the pulley engages. A quicker engagement means more power off the line, and more gradual engagement gives you more power at speed

NOTE: Recommend using a new belt with this kit. Belt and the belt drive-facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. Example, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.

Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.

Specifications: 

Includes the following Secondary slider (torque driver), Sliding sheave, Spring seat, O-rings, and Clutch nut.

•    1x Rear Pulley Plate OD: 118.5mm / Shaft ID: 17.43<21mm / OD: 34<45.1mm / H: 68.73mm
•    1x Secondary Slider Plate OD: 118.5mm / Funnel ID: 33.5mm / OD: 43mm / H: 32.70mm
•    1x Secondary Spring Seat/Funnel ID: 43mm / OD: 45<61mm / H: 30mm
•    3x Secondary Slider Pins OD: 5<6mm / H: 9.5mm
•    1x Stainless Steel Clutch Nut: M28
•    2x Rubber O-rings (pre-installed)
•    Made in Taiwan
•    Fit Clutch Nut Socket: 39mm
    Fit Clutch: 105mm / Shaft Nut: M10 / Washer: M10 / Bearing Seat47.4mm / Bell Spline: 22 Socket: 14mm
•    Fit Belt Size: 654669-18-30
•    Fit Compression Spring: 1k1.5k2k rpm
•    Fit Clutch Springs: 1k1.5k2k rpm
•    Fit Dowel Pin Set (8x10mm)
•    Fit DIO 50/90cc+

Supported Models: TFC CVT KIT (Part# 179-2); Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, and virtually any scooter engine with these measurements.

-----
Item Weight & Package Dimensions:
•    1.79 pounds | 5” (L) x 5” (W) x 3” (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
NCY Secondary Sliding Sheave Assembly (Honda Dio)
  • Stock: 37
  • Reward Points: 3
  • Part #: 1200-1251
Sold: 3
Views: 3023
$97.00
Ex Tax: $97.00
Price in reward points: 97

Included