Stage6 Secondary Sliding Sheave R/T Oversize Torque Boost (Aprilia, JOG, Zuma 50)
Description: Stage6 Secondary Sliding Sheave R/T Oversize Torque Boost Assembly for Aprilia, JOG, Zuma 50, and many other 50cc base engines. The Stage6 Oversize CVT. Different from conventional torque drivers that are manufactured from steel, this part consists of forged aluminum halves that are screwed to a guide piece. The halves have been CNC-machined, which guarantees high precision, especially of the surface angle. Special attention has been paid to ensuring an ideal surface roughness, as this has major influences on shifting characteristics. At the end of the manufacturing process, the surface structure is protected by applying a thick ceramic coating, so that the surface characteristics can be preserved as long as possible. Advantages of modular construction include reduced heat built-up, the noticeably lower weight, and the possibility to replace individual worn components. The CVT uses a guide piece with 38/41deg angles. Other guide pieces with angles of 39/42deg or 37/40deg are separately available. This feature is also something new for a CVT system.
NOTE: Recommend using a new belt with this kit. The belt and the belt drive-facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. For example, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.
Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch giving belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctite, torque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.
Includes the following Secondary slider (torque driver), Sliding sheave, Spring seat, O-rings, and Clutch nut.
• 1x Rear Pulley Plate OD: mm / Shaft ID: mm / OD: mm / H: mm
• 1x Secondary Slider Plate OD: mm / Funnel ID: mm / OD: mm / H: mm
• 1x Secondary Spring Seat/Funnel ID: mm / OD: mm / H: mm
• 3x Secondary Slider Pins OD: mm / H: mm
• 2x Rubber O-rings (pre-installed)
• 1x Stainless Steel Clutch Nut: M28
• Made in Italy
• Fit Aprilia 50
• Fit JOG 50
• Fit Zuma 50
Supported Models: APEX Pro MXR 50, Aprilia SR 50 LC, Benelli 491 RR 50, Benelli K2 50 LC, Beta Ark 50 LC, Beta Eikon 50, Garelli GSP 50, Italjet Dragset 50, KTM Ark 50 LC, MBK Nitro 50, MBK Nitro Naked 50, Malaguti F12 Phantom 50 LC, Malaguti F15 Firefox LC, Motowell Magnet RS 50, Streak Access 50, Tauris, Vento, Yamaha Aerox 50, Yamaha Jog RR 50, Yamaha Zuma 50, Yamati RX8 50 2-stroke, Znen and virtually any other scooter engine with these measurements.
Item Weight & Product Dimensions:
• 1.668 pounds | 4.663” (L) x 4.663” (W) x 2.769” (H)
From Same Category
- Stock: 40
- Reward Points: 11
- Part #: S6-5616615