Main Menu
Your Cart

TFC Cylinder 54mm 101cc Big Bore Kit w/Crankshaft 44.4mm (Honda Dio)

TFC Cylinder 54mm 101cc Big Bore Kit w/Crankshaft 44.4mm (Honda Dio)
TFC Cylinder 54mm 101cc Big Bore Kit w/Crankshaft 44.4mm (Honda Dio)
TFC Cylinder 54mm 101cc Big Bore Kit w/Crankshaft 44.4mm (Honda Dio)
TFC Cylinder 54mm 101cc Big Bore Kit w/Crankshaft 44.4mm (Honda Dio)
TFC Cylinder 54mm 101cc Big Bore Kit w/Crankshaft 44.4mm (Honda Dio)
TFC Cylinder 54mm 101cc Big Bore Kit w/Crankshaft 44.4mm (Honda Dio)
TFC Cylinder 54mm 101cc Big Bore Kit w/Crankshaft 44.4mm (Honda Dio)
TFC Cylinder 54mm 101cc Big Bore Kit w/Crankshaft 44.4mm (Honda Dio)

Description: TFC Cylinder 54mm 101cc Big Bore Kit with Crankshaft Stroker 44.4mm for Honda Dio/Elite S/SR engines 1994-01.

NOTE: Please measure with a caliper Honda Dio/Elite crankcase bore (opening) for 57.5mm cylinder outer diameter sleeve need a minimum of 57.7mm bore clearance or boring and machining are required.

Temperature Modification May Be Required: You'll need to heat the aluminum crankcase area where the crankshaft bearing side will be placed, in order to fit immediately the freezing TFC Crankshaft bearing side. Users assume full responsibility and risk doing so using this TFC Crankshaft.

Specifications:

Includes the following Cylinder, Piston + Rings, Gaskets (base gaskets, steelhead gasket), Wrist pin, Circlips, Studs, Bearings, Oil seals, Needle bearing, and Nuts.

•    1x Aluminum Piston: 54mm
•    3x Piston Rings: 54mm
•    2x Wrist Pin w/G-Clips
•    1x Cast-Iron Cylinder: 54mm
•    4x 6mm x 130mm Stud w/Nuts
•    Outer Sleeve Diameter: 57.5mm
•    Cylinder Height: 78mm
•    Exhaust Port Diameter: 31mm
•    1x Crankshaft: 41.4mm +3mm
•    Overall Stroke: 44.4mm
•    1x Flywheel Shaft Bearing ID: 20mm
•    1x Variator Shaft Bearing ID: 20mm
•    1x Oil Seal ID: 15mm / OD: 25.5mm / W: 7.15mm
•    1x Oil Seal ID: 19mm / OD: 31.3mm / W: 7.15mm
•    1x Oil Seal Plug
•    1x Needle Bearing: 17x12x13mm
•    Number of Rollers: 9
•    Length Steel Cage: 13mm
•    Diameter Steel Cage ID: 12mm
•    Diameter Steel Cage OD: 17mm
•    Made in Taiwan
•    Fit Taida Crankshaft 44.4 to 52.6mm
•    Fit DIO 50/90cc+ BORE

Supported Models: Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, and virtually any scooter engine with these measurements.

-----
Item Weight & Package Dimensions:
•    6.6 pounds | 7.5" (L) x 5.5" (W) x 5.25" (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
TFC Cylinder 54mm 101cc Big Bore Kit w/Crankshaft 44.4mm (Honda Dio)
  • Stock: 40
  • Reward Points: 20
  • Part #: 179-1
Sold: 0
Views: 10784
$509.00
Ex Tax: $509.00
Price in reward points: 509

Included