Main Menu
Your Cart

NCY CVT KIT Gen 4 (Vino, Zuma 125)

NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)
NCY CVT KIT Gen 4 (Vino, Zuma 125)

Description: NCY CVT KIT Gen 4 aka Super CVT transmission kit for Yamaha Vino 125, Yamaha Zuma 125, and Yamaha BWS 125 scooters. This Super Transmission Kit is one of the best dollar-for-dollar bolt-ons to improve your bike! Quicker acceleration, higher top speeds, and make your CVT the smoothest operating trans around! From rapid downshifting to slow cruising, this thing is smooth. Ultralight balanced components, oversized wear pads, and state-of-the-art Teflon coatings ensure superior performance and long service life.

NOTE: Must re-use stock variator boss, washers, clutch back-ramp plate, clutch nut, and nuts. Recommend using a new belt with this kit. The belt and the belt drive-facing plates KEEP DRY. All other areas apply moly-graphite grease when assembling. For example, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.

Installation: 1. Slack the belt by opening the CVT clutch giving belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.

Specifications:

100% NCY Products – OPTIONAL ADD-ON (IN RED).

Includes the following Drive face, Roller weights, Variator, Secondary slider, Springs, Clutch, and Clutch bell.

1.    Include NCY Drive Face, Drive Face CNC-Machined.
•    1x Aluminum CNC Machined Anodized Drive Face OD: 117.5mm / H: 14mm / W: 147.4gm
•    Splines: 15 / ID: 14.2<16mm / L: 7.6mm
2.    Includes NCY Variator 117.5mm Coated Gold, Roller weights, and Variator housing.
•    1x Alumin-Alloy Housing ID: 20.9mm / OD: 117.5mm / H: 35.88mm / W: 277.8gm
•    6x Roller Weights (red): 20x12mm 10gm
•    6x Roller Weights (red): 20x12mm 11gm
•    6x Roller Weights (red): 20x12mm 12gm 
3.    Includes NCY Secondary Slider, slider (torque driver), and O-rings.
•    1x Secondary Slider Plate OD: 138mm / Funnel ID: 41mm / OD: 50mm / H: 46.2mm
•    2x Rubber O-ring (pre-installed)
4.    Includes NCY Secondary Spring Seat, Bearings, Bearing cover, Bearing seat, and Secondary seat funnel. 
•    Seat Funnel ID: 50.2mm / OD: 52<54mm / H: 37.5mm
•    Bearing Cover ID: 52.2mm / OD: 63.9mm / H: 2.6mm
•    Bearing Seat ID: 52.2mm / OD: 66.5mmm / H: 6.4mm
•    1x Bearings Pack
5.    Include NCY Compression Spring 1500 RPM, Compression spring. (Make Selection)
•    1x Spring Comp (yellow): 1,500 RPM / L: 116mm
•    Spring ID: 54.5mm / OD: 58.2mm
•    Wire Gauge: 5mm
6.    Includes NCY Clutch Gen 4 Performance Green, Clutch housing, Clutch springs, and Clutch weights.
•    1x Clutch ID: 32.7<69mm / OD: 115.84mm / H: 38.15mm / W: 961.16gm
•    3x Clutch Spring (red): 2000 RPM
•    3x Clutch Weights (green)
7.    Include NCY Clutch Bell, Clutch Bell PTFE Coated.
•    1x Iron Clutch Bell (10-Spokes) ID: mm / OD: 129.6mm / H: 16.8<40.8mm / W: 595.33gm
•    Splines: 16 / ID: 14.5<16mm / OD: 129.6mm / H: 16.8<40.8mm
•    Made in Taiwan
•    Fit Belt Size: 757-21.4-28759-22-30 (Fit Vino ONLY)
•    Fit Belt Size790.5-21.9810-22-28 (Fit BWS, Zuma ONLY)
•    Fit Compression Spring: 1k1.5k2k rpm
•    Fit Clutch Springs: 1k1.5k2k rpm
•    Fit BWS 125
•    Fit Vino 125
•    Fit Zuma 125

Supported Models: Asia/European model Cygnus 125, Yamaha BWS 125, Yamaha Cygnus 125, Yamaha GTR 125, Yamaha Vino 125, Yamaha Zuma 125

-----
Item Weight & Package Dimensions:
•    7.63 pounds | 18” (L) x 7” (W) x 6.25” (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
NCY CVT KIT Gen 4 (Vino, Zuma 125)
  • Stock: 40
  • Reward Points: 10
  • Part #: 1200-1047
Sold: 0
Views: 2242
$267.95
Ex Tax: $267.95
Price in reward points: 268

Included