NCY CVT KIT (Metro, Ruckus GET) - CUSTOMIZABLE
Description: NCY CVT KIT GET aka Super CVT transmission kit for Metropolitan 2012 & older and all U.S. Honda Ruckus GET 50cc engines is one of the best dollar-for-dollar bolt-ons to improve your GET scooter transmission performance! Quicker acceleration, reach faster top speeds, and makes your GET CVT the smoothest running transmission in town! From rapid downshifting to slow cruising, this thing is smooth. Ultralight balanced components, oversized wear pads, and state-of-the-art polytetrafluoroethylene (PTFE) coatings ensure superior performance and long service life.
NOTE: Does not fit fuel-injected models. Must re-use stock variator ramp top, variator boss, washers, and nuts. Most parts also will fit Honda DIO's CVT. Recommend using a new belt with this kit. The belt and the belt drive-facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. For example, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.
Installation: 1. Slack the belt by opening the CVT clutch giving belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctite, torque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.
NCY CVT KIT (Metro, Ruckus GET) – THREE CUSTOMIZABLES.
Includes the following Drive face, Roller weights, Variator, Secondary sliding sheave assembly, Springs, Clutch, and Clutch bell.1. Include NCY Drive Face, Drive Face CNC-Machined.
• 1x Aluminum CNC Machined Anodized Drive Face ID: 13.5mm (Splines 26) / OD: 95mm / H: 20.19mm
2. Includes NCY Variator 95mm Performance, Roller weights, Variator housing, and Variator slides.
• 1x Alumin-Alloy Housing ID: 20mm / OD: 95mm / H: 31mm
• 6x Roller Weights (red): 16x13 5<9gm (Make Selection)
• 3x Plastic Slides (red)
3. Includes NCY Secondary Sliding Sheave Assembly, slider (torque driver), O-rings, and clutch nut.
• 1x Rear Pulley Plate OD: 118.5mm / Shaft ID: 17.43<21mm / OD: 34<45.1mm / H: 68.73mm
• 1x Secondary Slider Plate OD: 118.5mm / Funnel ID: 33.5mm / OD: 43mm / H: 32.70mm
• 1x Secondary Spring Seat/Funnel ID: 43mm / OD: 45<61mm / H: 30mm (Make Selection)
• 3x Secondary Slider Pins OD: 5<6mm / H: 9.5mm
• 1x Stainless Steel Clutch Nut: M28
4. Include NCY Compression Spring, Compression spring. (Make Selection)
• 1x Spring Comp: 1,000 RPM / L: 105mm
• Spring ID: 49.4mm / OD: 57.6mm
• Wire Gauge: 4mm
5. Includes NCY Clutch Performance, Clutch housing, Clutch springs, and Clutch weights.
• 1x Clutch ID: 24<28mm / OD: 105mm / H: 29.55mm
• 3x Clutch Springs (red): 2000 RPM
• 3x Clutch Weights (gray)
6. Include NCY Clutch Bell, Clutch bell.
• 1x Iron Clutch Bell Vented ID: 107mm / OD: 114.85mm / H: 34.54mm
• Splines: 22 / ID: 11<12mm / OD: 16.95mm / H: 21.75mm
• Made in Taiwan
• Fit Clutch Nut Socket: 39mm
• Fit Clutch Shaft Nut: M10 / Washer: M10 / Bearing Seat: 47.4mm / Socket: 14mm
• Fit Variator Nut: M12 / Washer: M12 / Socket: 17mm
• Fit Belt Size: 660-18-28 (Fit Metro ONLY)
• Fit Belt Size: 785-18-30 (Fit Ruckus ONLY)
• Fit Compression Spring: 1k, 1.5k, 2k rpm
• Fit Clutch Springs: 1k, 1.5k, 2k rpm
• Fit Dowel Pin Set (8x10mm)
• Fit GET 49/50cc
Supported Models: Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, Honda Zoomer NPS50, and virtually any scooter engine with these measurements.
Item Weight & Package Dimensions:
• 4.719 pounds | 17.98” (L) x 7” (W) x 6.4” (H)
People Also Bought
- Stock: 14
- Reward Points: 8
- Part #: 1200-1220